OpenELEC

XBMC subforum

Re: OpenELEC

Postby XoD » Tue Dec 23, 2014 2:37 pm

Hello, just a small update, I have made some progress.

See update on github thread : https://github.com/OpenELEC/OpenELEC.tv ... t-67955123

If someone is interessted to continue don't hesitate, I'm will not be able to work on this before 2 weeks or more.
XoD
 
Posts: 43
Joined: Thu May 29, 2014 12:52 pm

Re: OpenELEC

Postby vpeter » Wed Dec 24, 2014 7:50 am

Hi all,

like I wrote on a github the easier would be to patch "our" u-boot version with required changes for wandboard. I did the same for udoo board without a problem.
Also Linux kernel device tree must be better that what we have in "our" kernel. And this kernel can't be changed because whole imx6 project is using same components. Same problem I had with udoo board where I combine different parts of device tree to some working form. Now I have fully working system on udoo also ;)

I don't have this board so can help only with tips. If I can help let me know.

Peter
vpeter
 
Posts: 78
Joined: Wed Dec 24, 2014 7:44 am

Re: OpenELEC

Postby vpeter » Wed Dec 24, 2014 4:44 pm

If anyone would like to try OpenELEC image on wandboard quad here is the image: http://mirror1.openelec.tv/wandboard/Op ... uad.img.gz

Let me know if it boots and work.
vpeter
 
Posts: 78
Joined: Wed Dec 24, 2014 7:44 am

Re: OpenELEC

Postby synportack24 » Wed Dec 24, 2014 11:12 pm

Woah! can't thank both of you vpeter and XoD for your work! :!: :o :D

I've been a little tied up with grad school and work. Once I get back to my house I'll give this a go and report back
synportack24
 
Posts: 17
Joined: Mon Oct 20, 2014 10:56 pm

Re: OpenELEC

Postby XoD » Fri Dec 26, 2014 2:23 pm

Thank's vpeter, but like synportack42, I not be able to test before start/middle of january.

But If someone else can test, return are welcome :)
XoD
 
Posts: 43
Joined: Thu May 29, 2014 12:52 pm

Re: OpenELEC

Postby sgilani » Sun Dec 28, 2014 11:03 am

I have tested it and i only get the Wandboard Logo on boot and nothing else.
but i only copied the image with dd to an sdcard, was that correct?
sgilani
 
Posts: 5
Joined: Sun Dec 28, 2014 11:01 am

Re: OpenELEC

Postby vpeter » Sun Dec 28, 2014 11:13 am

sgilani, dd is correct.
Can you attach serial console and post log somewhere (pastebin for example)? Also in uEnv.txt add under bootargs line this two parameters progress debugging.
Last edited by vpeter on Sun Dec 28, 2014 11:58 am, edited 1 time in total.
vpeter
 
Posts: 78
Joined: Wed Dec 24, 2014 7:44 am

Re: OpenELEC

Postby sgilani » Sun Dec 28, 2014 11:52 am

unfortunately i don't have any pc with serial port or a usb/serial adapter at the moment. i can get one on 1-2 weeks..
sgilani
 
Posts: 5
Joined: Sun Dec 28, 2014 11:01 am

Re: OpenELEC

Postby vpeter » Sun Dec 28, 2014 11:56 am

sgilani, then just forget it. I'm sure someone else can test too.
vpeter
 
Posts: 78
Joined: Wed Dec 24, 2014 7:44 am

Re: OpenELEC

Postby sgilani » Sun Dec 28, 2014 1:06 pm

found a way:
Code: Select all
U-Boot 2013.10-rc4 (Dec 24 2014 - 17:32:07)

CPU:   Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: Wandboard
DRAM:  2 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0
mmc0 is current device
SD/MMC found on device 0
Checking for: /uEnv.txt ...
Unknown command 'load' - try 'help'
## Warning: Input data exceeds 1048576 bytes - truncated
## Info: input data size = 1048578 = 0x100002
Loaded environment from /uEnv.txt
Checking if uenvcmd is set ...
Checking for: /boot/uEnv.txt ...
Unknown command 'load' - try 'help'
## Warning: Input data exceeds 1048576 bytes - truncated
## Info: input data size = 1048578 = 0x100002
Loaded environment from /boot/uEnv.txt
Checking if uname_r is set in /boot/uEnv.txt...
Unknown command 'load' - try 'help'
## Warning: Input data exceeds 1048576 bytes - truncated
## Info: input data size = 1048578 = 0x100002
Loaded environment from /boot/uEnv.txt
Checking if uname_r is set in /boot/uEnv.txt...
Unknown command 'load' - try 'help'
## Warning: Input data exceeds 1048576 bytes - truncated
## Info: input data size = 1048578 = 0x100002
Loaded environment from /boot/uEnv.txt
Checking if uname_r is set in /boot/uEnv.txt...
Unknown command 'load' - try 'help'
## Warning: Input data exceeds 1048576 bytes - truncated
## Info: input data size = 1048578 = 0x100002
Loaded environment from /boot/uEnv.txt
Checking if uname_r is set in /boot/uEnv.txt...
Unknown command 'load' - try 'help'
## Warning: Input data exceeds 1048576 bytes - truncated
## Info: input data size = 1048578 = 0x100002
Loaded environment from /boot/uEnv.txt
Checking if uname_r is set in /boot/uEnv.txt...
Unknown command 'load' - try 'help'
## Warning: Input data exceeds 1048576 bytes - truncated
## Info: input data size = 1048578 = 0x100002
Loaded environment from /boot/uEnv.txt
Checking if uname_r is set in /boot/uEnv.txt...
Unknown command 'load' - try 'help'
## Warning: Input data exceeds 1048576 bytes - truncated
## Info: input data size = 1048578 = 0x100002
Loaded environment from /boot/uEnv.txt
Checking if uname_r is set in /boot/uEnv.txt...
MMC: no card present
mmc1(part 0) is current device
MMC: no card present
=>
sgilani
 
Posts: 5
Joined: Sun Dec 28, 2014 11:01 am

PreviousNext

Return to Software - XBMC

Who is online

Users browsing this forum: No registered users and 21 guests